Gledhill Repairs
Would you like to react to this message? Create an account in a few clicks or log in to continue.

PulsaCoil III - After topping up water tank, no green light, no heat

3 posters

Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty PulsaCoil III - After topping up water tank, no green light, no heat

Post  mtyler Sun Mar 03, 2013 9:51 am

Hi, I have gone through all the various posts and read through the manual but have failed to get my PulsaCoil III boiler working. It was working yesterday evening after we have been away for a week on holiday. However, by the end of the evening the lights on the boiler had gone off and there was no hot water. I tried topping up the upper water tank but the green lights have not turned on yet and I tried turning the switches off/on and even tried the booster switch. Nothing is working. When we turn on a hot water tap the boiler is making noises like it should be doing something however there is no hot water coming out. We have always had issues with the hot water being sporadic (would only last for 1 shower) in spite of calling people out to look at it several times. Any suggestions or tips would be gratefully appreciated! Thank you.

mtyler

Posts : 4
Join date : 2013-03-03

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  Mario.S Sun Mar 03, 2013 12:08 pm

This could be one of those rear thing like the water level switch in your top tank is faulty, this also stops the Pulsacoil to heat up. but first check the level in your top tank, if the water is about half way up.
I hope this helps
Mario at Mario's Boiler Service

Mario.S

Posts : 224
Join date : 2011-12-10
Location : Fareham / Hampshire

http://www.marios-boiler-service.co.uk/

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  mtyler Sun Mar 03, 2013 2:49 pm

Hi Mario - I just checked and the upper tank is halfway full. The green lights are back on now, however there is still no hot water. Not sure what else to do as have already flicked the on/off switches. Any ideas? Thank you again for your response!

mtyler

Posts : 4
Join date : 2013-03-03

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  Mario.S Sun Mar 03, 2013 3:09 pm

There will be no hot water till tomorrow morning, remember the Pulsacoil is a night storage water heater !! and if the led's just come on, you have to wait till tomorrow.
If no hot water tomorrow morning, green led's are on, touch the pipe coming out of the main boiler before going to the Exchanger ( the big silver one with the 4 connected pipes to it) on the boiler if there are hot, if not, your Immersion heater in the bottom of the tank is faulty ( or there is no electricity going to it ( timer fauty ?), if hot, your Pump is faulty, pcb or sensors ( hard to point if I am not testing it in person)
regards Mario

Mario.S

Posts : 224
Join date : 2011-12-10
Location : Fareham / Hampshire

http://www.marios-boiler-service.co.uk/

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  Mario.S Sun Mar 03, 2013 3:29 pm

If there is still no hot water tomorrow, you need to lock out for an competent engineer in your area, who is able to repair Gledhill boiler, most " ornery" Plumbers aren't. ( course I am "only" covering 50 miles or so, around Fareham / Hampshire, but lock at my website )If they say you need a new Boiler, send them off !!!
kind regards Mario

Mario.S

Posts : 224
Join date : 2011-12-10
Location : Fareham / Hampshire

http://www.marios-boiler-service.co.uk/

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  mtyler Sun Mar 03, 2013 4:06 pm

Thank you for all your help Mario. Fingers crossed we have hot water in the morning. Will keep you posted!

mtyler

Posts : 4
Join date : 2013-03-03

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  mtyler Mon Mar 04, 2013 8:04 am

Just checked, still no hot water. Anything else we can try?

mtyler

Posts : 4
Join date : 2013-03-03

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Check the overheat stat

Post  sunny.sahdev Mon Sep 02, 2013 8:08 am

Check the overheat stat has not popped out. If the tank is low in water level and the element switched on, it causes the overheat stat to pop out for safety reasons.
If that doesn't work, try the booster switch and leave that on for about 3 hours.

Also requested this free self check mini guide which explains the basic - just to make sure everything else is being done correctly.

Pulsacoil Repair <-- Self check guide link for you

sunny.sahdev

Posts : 383
Join date : 2013-08-21
Age : 38
Location : Vedhas Limited, 960 Capability Green

http://www.vedhas.co.uk/vedhas-what-we-do/pulsacoil-repair/#

Back to top Go down

PulsaCoil III - After topping up water tank, no green light, no heat Empty Re: PulsaCoil III - After topping up water tank, no green light, no heat

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum