Gledhill Repairs
Would you like to react to this message? Create an account in a few clicks or log in to continue.

no feed to boiler pump

2 posters

Go down

no feed to boiler pump Empty no feed to boiler pump

Post  Roydaniels Thu Feb 13, 2014 12:25 pm


I have changed the pcb on my gledhil systemate 2000 as it was exhibiting a lot of problems. I have installed a new pcb but now boiler pump is not getting getting a signal. I have by-passed it to run constant to restore heating but this is not ideal. Any ideas? The led illuminates and and the boiler fires as normal but the pump just doesn't get the message. Could this just be a sensor or a faulty pub?

Roydaniels

Posts : 6
Join date : 2014-02-07

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  mike Fri Feb 14, 2014 6:28 am

Could be the PCB
Fitted it as per the book etc?
Old one was doing what?
Check all connections etc.
Mike

mike

Posts : 1747
Join date : 2009-10-08
Age : 71
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

no feed to boiler pump Empty no feef to boiler pump

Post  Roydaniels Sun Feb 16, 2014 10:38 am

The New pcb was fitted as per the book with jumper in no5 for commissioning And then removed. Connections all seem ok. Old board was not sending signal to boiler, would not run heating pump, the dhw pump ran constantly and the display showed 'on' all the time but would not give any readings for sensors. My next step is to phone the Gledhill technical help line. I want them to help me find out if the board is ok.

Roydaniels

Posts : 6
Join date : 2014-02-07

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  mike Sun Feb 16, 2014 12:32 pm

Can you read the sensors now?

mike

Posts : 1747
Join date : 2009-10-08
Age : 71
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  Roydaniels Sun Feb 16, 2014 1:21 pm

I can read all the sensors now and everything seems fine. There doesn't seem to be any odd readings. The only other thing I have noticed is, the heating can be switched on and the heating pump will run before the store reaches 65deg. The book says this should not happen.

Roydaniels

Posts : 6
Join date : 2014-02-07

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  mike Sun Feb 16, 2014 1:27 pm

I would say PCB is faulty.
You have the jumpers on correct.
Try setting it again.
Mike

mike

Posts : 1747
Join date : 2009-10-08
Age : 71
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  Roydaniels Sun Feb 16, 2014 1:37 pm

The jumpers are correct (1&4). I think it is the pcb but I need confirmation and I am not sure how to do this. What do you mean by setting it again? Switch off mains and start as if recommissioning?
Very grateful for your help.

Roydaniels

Posts : 6
Join date : 2014-02-07

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  mike Sun Feb 16, 2014 1:41 pm

Yes I would try it again.

mike

Posts : 1747
Join date : 2009-10-08
Age : 71
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

no feed to boiler pump Empty Re: no feed to boiler pump

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum