Gledhill Repairs
Would you like to react to this message? Create an account in a few clicks or log in to continue.

How to install a PCB board into a Boilermate 2000

4 posters

Go down

How to install a PCB board into a Boilermate 2000 Empty How to install a PCB board into a Boilermate 2000

Post  silversurfer Mon Apr 30, 2012 4:30 pm

My BM200 currently has a blown PCB which for which I have a replacement. I now need to install but would appreciate if someone could give me the step by step instructions of how to install a PCB board into a BM2000. I have downloaded the instruction manual from the Gledhill site but it is not very clear.

Thanks in advance for any advice.

silversurfer

Posts : 1
Join date : 2012-04-30

Back to top Go down

How to install a PCB board into a Boilermate 2000 Empty Re: How to install a PCB board into a Boilermate 2000

Post  mike Tue May 01, 2012 5:27 pm

The board should come with instructions.
Turn off power.
Remove old board.
Remove jumpers from old board and place IN THE SAME PLACE on the new one.
Put a jumper on number 5.
Fit board DO NOT TOUCH IT I USE GLOVES!
Switch on and let the unit go through its actions.
Remove jumper on 5
Switch back on and all done.
Why did the board blow?
Mike
MGC/H2O
Norwich
Norfolk

mike

Posts : 1747
Join date : 2009-10-08
Age : 70
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

How to install a PCB board into a Boilermate 2000 Empty Used PCB

Post  Magoo Sat Feb 18, 2017 9:53 am

mike wrote:The board should come with instructions.
Turn off power.
Remove old board.
Remove jumpers from old board and place IN THE SAME PLACE on the new one.
Put a jumper on number 5.
Fit board DO NOT TOUCH IT I USE GLOVES!
Switch on and let the unit go through its actions.
Remove jumper on 5
Switch back on and all done.
Why did the board blow?
Mike
MGC/H2O
Norwich
Norfolk

Hi Mike
Do I need to use the same installation process for a used PCB, or is the process of using a jumper on position 5 for new boards only?
Many thanks

Magoo

Posts : 3
Join date : 2013-11-13

Back to top Go down

How to install a PCB board into a Boilermate 2000 Empty Re: How to install a PCB board into a Boilermate 2000

Post  mike Sat Feb 18, 2017 3:43 pm

Same for old or new

Mike

mike

Posts : 1747
Join date : 2009-10-08
Age : 70
Location : Norwich

http://www.mgch20.co.uk

Back to top Go down

How to install a PCB board into a Boilermate 2000 Empty Jumoer 5 on GT155

Post  mmartin Tue Feb 21, 2017 4:26 am

The jumper on position 5 on a GT155 makes it run through a diagnostic program that switches each output on an off briefly, the 4 green LED will cycle on and off breifly from bottom to top and after the last one has gone off the heat exchanger pump will run for a second or two. I believe you can replace the board without having to fit the 5th jumper, well I have anyway without any adverse effects. It may be handy of course just to establish that the outputs and pumps and the boiler power etc. is working.

mmartin

Posts : 166
Join date : 2017-02-12
Location : Nottinghamshire

http://www.murraymartin.co.uk

Back to top Go down

How to install a PCB board into a Boilermate 2000 Empty Re: How to install a PCB board into a Boilermate 2000

Post  Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum